OOAK Artist Emporium - Polymer Clay Tools

Royal Langnickel Soft Grip Ball Stylus Set

Royal Langnickel Soft Grip Embossing Stylus

This is a must for sculptures to stand freely in poses not possible any other
way. The brass tube is attached to the leg or arm of an armature and then
clay is sculpted around it in the normal way.

The rod is inserted into the display base of choice. When the sculpture is
completed, insert the tube end onto the rod...your sculpture will stand!

Tube and tube can be used when sculpting hands and heads separately
and then attached to your armature later and polymer clay added to blend in
the hand and arm. You can also turn hands to the desired position without
damaging them.

Rod and Tube is sold in 12 inch long pieces.

click images for a larger view.

For cutting rods, I recommend using a
cutting wheel disk made for a dremel tool.
It will make a clean end cut without the
need to reshape.

Click on the right image for larger view of
dremel tool.

See Dremel Tool Here

With any power tools, safety should be first.
Always wear protective safety glasses.

Small hobby tube cutter will work to cut the larger Round tube & tube ONLY.

It's simple to use. Place the tube in the V and turn the thumb screw until it stops on the
tube. Then gently turn the cutter in a circular motion around the tube and then tighten the
thumbscrew again and turn the cutter again. Continue to tighten the thumbscrew and then
turning the cutter until the tube is completely cut.
This tool is not recommended for cutting rods or SQUARE TUBES

.95 each

Studio by Sculpey Glaze

Sculpey has discontinued the Studio line.
When these are gone they will be replaced
with the new Sculpey Glazes.

Add a durable seal or finish to baked polymer clay
items with these compatible acrylic water-based
finishes. Apply thin washes with a small brush. Thin
glazes with water if desired.

Available in SATIN and GLOSS finishes.

2 ounce Satin 4.75 ea

Sponge Sanders
are flexible and are used to reduce irregularities and fingerprints left in baked polymer clay. Start with the Medium 120-180
grit to take down lumps...use the Super Fine 500-600 grit to reduce sanding marks and smooth. Use the Ultra Fine
800-1000 grit to give a satiny smooth finish.

2.25 ea

These ball stylus tools are originally designed to
use with embossing on card stock. They are
also perfect for use with sculpting in polymer
clay. These tools are clear acrylic with soft gel
grips. Sold in a set of three.

4.25 set

__________________________________________________________________

Set includes these
sizes

Sm .50mm - 1.0mm
Med 1.0mm - 1.5mm
Lg 1.5mm - 3.0mm

__________________________________________________________________

Brass Rod and Tube

Small Rod & Tube set -
Recommended for sculptures
up to 8 inches tall
2.50 per foot/set

Large Rod & Tube set-
Recommended for sculptures
9 to 18 inches tall
3.75 per foot/set

Tube & Tube set-
Recommended for attaching
sculpted hands and head
3.50 per foot/set

My Recommendation for cutting small rods and large rods and SQUARE ROD & TUBE

MicroPerm Pens are permanent, write
on any surface including:

glass
plastic
polymer clay (does not bleed)
transparencies
vellum
photographs
CD's

Provide ultrafine lines for precise detail
and precision. Will not smear.
.25mm tip - black ink

2.50 each

Fine enough to initial a 6mm glass bead

___________________________________________________________________

MicroPerm

Polymer Clay Tools & Essentials

Page 1 2

Sculpey Clay Softener

Is used for reconstituting polymer clay products which have become less

pliable due

to warm storage conditions, or to soften the standard

consistency of products. Add a

few drops to any brand of polymer clay

and knead.

Sculpey Clay Softener

is also great

for smoothing out tool

marks and fingerprints left in clay from handling.

Sculpey Diluent can also be used as a polymer "glue" by brushing it onto

the sides

you wish to join together.

3.85 ea

(This is the same product as Prosculpt Smoothing Oil)

Back Next

Round Rods and Tubes may be
purchased separately

NEW! Square Rod & Tube and Tube & Tube
Square rod and tube is ideal for sculptures that must be stationary. If the pose of the sculpture is designed in such a way
that turning would not be desirable, then square tubing would be the solution for that issue. Sculptures that appear to fly or
swim can sometimes roll with regular round tubing. Square tubing eliminates any turning. It stays where you put it!
Depending on the pose, this combination will work on most any size sculpture up to 18 inches

5.95 per set

I recommend a jeweler's saw for
cutting Square tube & tube or the
Dremel cut off wheel.

The X-Acto Swivel knife is perfect for cutting around curves or for small, intricate details! With a
unique, light duty steel blade that rotates a full 360°, you can get precise cuts around virtually
any shape in paper, cardstock, film, stencils, decals, and more. No crafter or scrapbook artist
should be without this versatile knife! This knive comes with one blade.
Uses X-Acto Craft Swivel replacement blades.

X-ACTO

____________________________________________________________________

X-ACTO Swivel Knife Replacement Blades.
This pack contains 3 replacement blades
specifically for the Xacto Swivel knife which
was designed for easily cutting curves of all
degrees into light-weight materials.

2.85 ea - 3pk